Introduction to USB/PPIM+  6ES7 901-3DB30-0XA0

Optoelectronic isolated USB Siemens S7-200PLC multi-master station PPI programming cable,directly use the STEP7 MicroWIN software to communicate,no need to install driver,support PPI,multi-master station PPI and advanced PPI,support 187.5Kbps high speed communication,just the same as 6ES7 901-3DB30-0XA0,3 meters,with communication indicator.

USB / PPIM + is the PPI Multi-Master programming Cable which with USB interface, to realize the level conversion and various of PPI protocol conversion from USB to RS485.Many cheap USB / PPI cable on the market simulate USB to virtual serial (COM port) to realize the communications, it’s commonly known as "pseudo-USB interface". The cable only convert the level from USB to RS485, can only support the normal PPI Protocol. But the USB / PPIM + is the real USB interface cable, without installing drivers, directly use the USB option in STEP7 Micre / WIN software, support PPI, Advanced PPI,and Multiple Master Network Protocol. The cable support the 187.5 Kbps high-speed communications, and take charge of the Multiple Master Network.

This cable is 100% compatible with Siemens PPI Multi-Master USB Cable 6 ES7 901-3DB30-0XA0, and the only difference is that the work power supply from the computer's USB port through the DC / DC isolation, no longer powered by the PLC port. It’s easy to extend communications distance of the RS485 without considering the power supply. The two-color LED on the converter box indicates data’s transceiving status.

USB/PPIM+ is designed for industrial-type photoelectric isolation cable. USB port and RS485 ports are equipped with surge protection and anti-lightning protection circuitry, which can be Hot plug. It’s applicable to the entire Siemens S7-200 Series PLC It’s particularly suited to the industrial scene which the communications interface is more easily damaged because of the greater interference. The protection circuit ensures the safe operation of the system.

Outline configuration of USB/PPIM+:

signals definition of the RS485-Block (DB9M) of the USB/PPIM+

Features and technological index of USB/PPIM+:

● support USB / PPIM + programming software version: STEP7 Micro / WIN V4.0 and above, without installing drivers, directly use the USB option in Local Connection.
● USB is fully compatible with USB V1.1 norms and USB V2.0
● USB bus-powered, 5 VDC, the power consumption is about 100 mA, with over current protection
● optical isolation voltage: 1000 VDC (up to 3000 VDC, it should be declared when making an order)
● USB port with anti-surge protection, RS485 port with 500 W anti-lightning protection and over current protection
● support PPI baud rate: 9.6 Kbps, 19.2Kbps, 187.5Kbps
● support the communication protocol: PPI, senior PPI, multi-master PPI.
● support long-distance communications, the largest communications distance is 2,000 meters (9.6 Kbps) or 1 km(187.5Kbps).
● each PC only supports a USB cable programming
● temperature: -20 ~ +75 'C
● Cable length: three meters, colors: black

Usage of USB/PPIM+:

1, Enter STEP7 Micro / WIN programming software and click "Settings PG / PC interface", check the "PC / PPI cable (PPI)" and click "Properties…" button.
2, Select "USB" option in "Local Connection".
3, Set up the Station Parameters settings in "PPI" as following: Address: 0, Timeout: 1s .
Set up the Network Parameters in "PPI" in accordance with the needs of you. You can choose any of the following:
Advanced PPI: check the Advanced PPI.
Multiple Master Network: check Multiple Master Network.
General PPI: do not check any of option, which is the default option.
select a baud rate as the same with the PLC. If you do not know that the PLC baud rate can be arbitrary choice one.Click "OK" button to return to the main menu interface.
4, click on the main menu interface of "communication" button to enter the PLC interface connection, check the "search all baud rate" box, and then double-click on the "Double-click refresh”. After a while of searching ,the PLC model And address and other information will display on the software, it’s means that connect successfully with the PLC. Click the "confirmation" button to conduct upload, download, and other operating.

PPI Multi-Master Cable of USB/PPIM+ no longer support the early version of the low CPU21X series PLC.

PPI Multi-Master Cable of USB/PPIM+ do not support Freeport communication and MODEM communication.

Long-distance communications:

The largest communications range between the USB/PPIM+ and PLC are up to 2 kilometers (9.6K bps) or 1 km(187.5Kbps),when external plus terminals 120 ohm resistance is needed to connect between the pin3 and pin8 of the RS485 ports (DB9 Male) to eliminate signal reflection. And a PFB-G Bus Isolators is needed to install at the end of PLC. 0.22 mm2 or more unshielded twisted pair lines are used for Communications. When the distance is longer than the length of cable, a RS485 repeaters (model: E485GP), can be installed in the bus for extending the distance.

Because the power of USB / PPIM + all supplied from the USB ports of the computer, you do not need to consider power supply when extended the length of cable. It’s better than the similar products of Siemens.

Please Note: USB interface cable cannot be extended.

Part#: USB/PPIM+

Introduction to USB/PPI+  6ES7 901-3DB30-0XA0

USB/PPI+ programming cable simulates USB port as traditional serial port (usually COM3), which enables existing programming software(STEP 7-MicroWin) to communicate through simulated traditional port and PLC devices.

The working power supply of this cable is from the USB port and PLC programming interface. The two-color LED on the converter box indicates data’s transceiving status.

USB/PPI+  is optoelectronic isolated,suitable for Siemens S7-200 series PLC,especially for the strong interfere and easily damaged communication interface industry scene.The safeguard in the circuit guarantees the safely running of the system.

USB/PPI+ principle and figure structure:

signals definition of the RS485-Block (DB9M) of the USB/PPI+

Functions

• Support Windows2000/Windows XP
• Support STEP7 Micro/WIN V3.2 and higher
• Fully compatible with USB V1.1 and USB CDC V1.1
• Power supply by USB bus and PLC programming port.
• Baud rate: 300 bps ~ 1Mbps automatically adapt to the standard baud rate.
• Support UART data format: data bits: 7-8; stop bit: 1, 2; check-bit: odd / even / no parity
• Support long distance communication up to 2000m(9600 bps).
• Working temperature -20~+75'C
• Length 3 meters.Color:black
• One pc supports one USB programming cable only

System requirement

Please make sure your PC is IBM PC compatible and has the following system requirements before using the USB programming cable.

• Intel is compatible with 586DX4-100MHz CPU or higher
• A standard USB port (4-pin A plug)
• Operating system is Windows2000 or Windows XP

The setting of driver procedure

Please set the driver procedure according to the following steps:

1. Turning on PC power that will connect the USB programming cable and make sure the USB port working well.
2. Put the USB programming cable into USB port and Windows will detect the device and help to add new hardware and jump to new device setting. Insert the driver CD and click “next” to continue, or select the driver on the hard disk.

If Windows does not show “Found New Hardware Wizard”, please click “Universal Serial bus controllers” in the hardware list of device manager, and choose the USB device with question mark. Click the right key of mouse and operate to update driver procedure.