6ES7332-5HD01-0AB0 Siemens Analog output module
Introduction to Siemens 6ES7332-5HD01-0AB0
Properties of Siemens 6ES7332-5HD01-0AB0
● 4 outputs in one group
● The output can be selected by individual channel
– Voltage output
– Current output
● Resolution 12 bits
● Programmable diagnostics and diagnostic interrupt
● Electrically isolated to backplane bus interface and load voltage
● Supports parameter reassignment in RUN
Diagnostics
For information on diagnostic messages at the "group diagnostics" parameter, refer to
chapter Diagnostic messages of analog output modules (Page 310).
Terminal assignment
The diagrams below show various wiring options.
Note
When you switch the rated load voltage (L+) off and on, the outputs can return incorrect
voltage/current values for the duration of about 500 ms.
Wiring: 2 and 4-wire connection for voltage output
The following Fig. represents the 2-wire connection with no compensation for line resistors
and the 4-wire connection with compensation for line resistors.
Wiring: Current output
Technical specifications of 6ES7332-5HD01-0AB0
Parameter reassignment in RUN
If you reassign parameters in RUN, the following special characteristic applies.
SF LED is lit:
If a diagnostics was pending prior to reconfiguration, the SF LEDs (on CPU, IM or module)
may be lit even though diagnostics is no longer pending and the module is operating correctly.
Solution:
● Only assign new parameters if no diagnostics is pending, or
● unplug module and plug it in again.
Output ranges of SM 332; AO 4 x 12 Bit
Introduction
You can configure the outputs for operation as voltage or current outputs, or disable them.
You program the outputs at the "output type" parameter in STEP 7.
The output type "Voltage" and output range "± 10 V" are set by default at the module. You
can always use this combination of output type and range without having to program the
SM 332; AO 4 x 12 Bit in STEP 7.
Output ranges
Program the voltage and current output ranges in STEP 7.
Output ranges of SM 332; AO 4 x 12 Bit
Selected type of output | Output range |
Voltage | 1 V to 5 V 0 V to 10 V |
± 10 V | |
Current | 0 mA to 20 mA |
4 mA to 20 mA | |
± 20 mA |
Overview of the parameters of SM 332; AO 4 x 12 Bit
Assigning parameters to channels
The parameters can be set separately at each output channel of SM 332; AO 4 x 12 Bit. You can assign separate parameters to each output channel.
Assign the parameters you set at the SFCs in the user program to the channel groups. Each output channel of SM 332; AO 4 x 12 Bit is thus assigned to a channel group, i.e. output channel 0 > channel group 0, for example.
Note
The output may carry incorrect interim values if you modify output ranges while SM 332;AO 4 x 12 Bit is in RUN.
Additional information on SM 332; AO 4 x 12 Bit
Unused channels
To take unused output channels of SM 332; AO 4 x 12 Bit off power, set the "disabled" argument at the "output type" parameter. Disabled channels do not have to be wired.
Line continuity check
SM 332; AO 4 x 12 Bit only performs a line continuity check at the current outputs.In output ranges 0 mA to 20mA and ±20 mA, a "reliable" wire-break check is not possible for output values of-20s to ±200 μA.
Short-circuit test
SM 332; AO 4 x 12 Bit only performs a short-circuit test at the voltage outputs.
Substitute values
You can configure the SM 332; AO 4 x 12 Bit for CPU STOP mode as follows: Outputs off power, hold last value or set substitute values. The set substitute values must lie within the output range.
USER'S manual PDF of 332-5HD01, please refer from Page 481- Page 489:
S7-300 Modules data & USER'S MANUAL
Our company (Kollewin Technology CO., Limited) have a new product,
named 6ES7332-5HD01-0AB0,
it is 100% compatible with Siemens original part.
Part#: 6ES7332-5HD01-0AB0
Description: S7-300 Analog onput module
Manufacturer: Kollewin
Approx. Weight: 0.3 Kg
Warranty: 1 year
Origin: China
Here, you also need 1 piece of 20pin front connector to connect with it.
Our compatible 6ES7 392-1AJ00-0AA0 can meet your requirements.
6ES7 392-1AJ00-0AA0 @USD10.50/pc
Technical data sheet of our SM 332 6ES7332-5HD01-0AB0
Model |
SM332 4AO |
Product Description |
4AO; Resolution:12bits; High-accuracy |
Power consumption |
|
·From bus current consumption |
40mA |
·From L+ |
40mA |
·Power loss |
3W |
Number of analog outputs |
4 |
Load voltage+rated value |
24V |
Shielded cable length,Max |
200m |
Voltage output, Max,short circuit Current |
Yes |
Voltage output, Short circuit current(Max) |
25mA |
Voltage output, Open-circuit current,Max |
18V |
Load impedance |
|
·Voltage outputs,Min |
1KΩ |
·current outputs,Max |
500Ω |
Output ranges |
|
·voltage |
±10V,0~10V,1~5V |
·current |
±20mA,0~20mA,4~20mA |
D/A resolution |
12bit |
conversion time(per channel) |
Max:0.8ms |
Setting time |
|
·Resistive loads |
0.1ms |
·Capacitive loads |
3.3ms |
·Inductive loads |
0.5ms |
Output cross talk |
>40dB |
Tolerance(Over entire temperature range) |
|
·Voltage output |
±0.5% |
·Current output |
±0.6% |
Diagnostic interrupt |
None |
Group fault error |
Red LED |
Isolution tested for contact |
|
·Between channels and backplane bus |
Yes |
·Between channels and load voltage L+ |
Yes |
Front connector |
20-pin |
Dimensions(W x H x D)(mm) |
40×125×120 |
Order Number |
332-5HD01-0AB0 |
Picture of 6ES7332-5HD01-0AB0
More compatible Siemens S7-200/300 modules we can offer:
Model | Product Description |
SM7-200 DIGITAL MODULE | |
6ES7221-1BH22-0XA0 | EM221 16 DI 24V DC |
6ES7221-1BL22-0XA0 | EM221 32 DI 24V DC |
6ES7222-1BF22-0XA0 | EM222 8DO,DC 24V |
6ES7222-1HF22-0XA0 | EM222 8DO,relay |
6ES7222-1BH22-0XA0 | EM222 16 DO 24V DC |
6ES7222-1HH22-0XA0 | EM222 16 DO RELAY |
6ES7222-1BL22-0XA0 | EM222 32 DO 24V DC |
6ES7223-1HF22-0XA0 | EM223 4DI/4DO,DC 24V relay |
6ES7223-1BH22-0XA0 | EM223 8 DI/ 8 DO 24V DC |
6ES7223-1PH22-0XA0 | EM223 8 DI 24V DC/8 DO RELAY |
6ES7223-1BL22-0XA0 | EM223 16 DI/ 16 DO 24V DC |
6ES7223-1PL22-0XA0 | EM223 16 DI 24V DC/ 16 DO RELAY |
6ES7223-1BF22-0XA0 | 4 DI/4DO,24 VDC |
6ES7221-1BF22-0XA0 | 8 DI,24V DC |
SM7-200 ANALOG MODULE | |
6ES7231-0HC22-0XA0 | EM231 4 AI x 12 Bits |
6ES7231-0HF22-0XA0 | EM231 8 AI x 12/11 BIT |
6ES7231-7PC22-0XA0 | EM231 4 RTD |
6ES7231-7PD22-0XA0 | EM231 4 TC |
6ES7231-7PH22-0XA0 | EM231 8 TC |
6ES7231-7PL22-0XA0 | 16AI, T/C INPUT MOD, 16BIT |
6ES7231-7PB22-0XA0 | 2AI, RTD INPUT MOD. 16BIT |
6ES7232-0HB22-0XA0 | EM232 2 AO x 12 Bits |
6ES7232-0HD22-0XA0 | EM232 4 AO x 12 Bits |
6ES7235-0KD22-0XA0 | EM235 4 AI/ 1 AO x 12 Bits |
SM7-300 DIGITAL MODULE | |
6ES7321-1BH02-0AA0 | SM321 16 DI 24 VDC |
6ES7321-1FH00-0AA0 | SM321 16 DI AC 230V |
6ES7321-1BL00-0AA0 | SM321 32 DI 24 VDC |
6ES7322-1BF01-0AA0 | SM322,8DO,24VDC,2A |
6ES7322-1BH01-0AA0 | SM322 16 DO 24 VDC/ 0.5A |
6ES7322-1HH01-0AA0 | SM322 16 DO RELAY |
6ES7322-1BL00-0AA0 | SM322 32 DO 24V DC/0.5A |
6ES7323-1BL00-0AA0 | SM323 16DI 24V DC/ 16DO 24V DC 0.5A |
SM7-300 ANALOG MODULE | |
6ES7331-1KF01-0AB0 | SM331 8 AI x 13 Bits |
6ES7331-7KF02-0AB0 | SM331 8 AI X 14 Bits |
6ES7331-7PF01-0AB0 | SM331 8 AI,RTD |
6ES7331-7PF11-0AB0 | SM331 8 AI,TC |
6ES7332-5HD01-0AB0 | SM332 4 AO x 12 Bits |
6ES7332-5HF00-0AB0 | SM 332 8 AO x 12 BITS |
SIMATIC DP IM 153 | |
6ES7153-1AA03-0XB0 |
SIMATIC DP, INTERFACE IM 153-1, FOR ET 200M, FOR MAX. 8 S7-300 MODULES |
6ES7365-0BA01-0AA0 | IM 365 Rack expansion module,be deployed with a central controller and a expansion rack |
More pictures for your reference:
Please feel free to contact me for any question!
Contact person: Miss Nancy
E-mail: nancy@kollewin.com
Tel: +86-0755-26898905-8006
Website: www.kollewin.com
Recent Comments