USB/MPI+ V2.0:USB isolated adapter for Siemens S7-300/400 PLC, replace 6ES7 972-0CB20-0XA0

USB/MPI+ V2.0:USB to RS485 isolated adapter for SIEMENS S7-200/300/400 PLC,replace 6ES7 972-0CB20-0XA0

6ES7 972-0CB20-0XA0          SIMATIC S7, PC ADAPTER USB

SIMATIC S7, PC ADAPTER USB F. CONNECTION OF S7-200/300/ 400, C7; WITH USB-CABLE (5M) CAN BE USED UNDER WINXP/VISTA/ WINDOWS 7 32/64BIT

Please read below data sheet of Siemens original 6ES7972-0CB20-0XA0:

-	SIMATIC S7, PC ADAPTER USB F. CONNECTION OF S7-200/300/ 400, C7; WITH USB-CABLE (5M) CAN BE USED UNDER WINXP/VISTA/ WINDOWS 7 32/64BIT
Supply voltage
24 V DC	Yes
Input current
Current consumption, typ.	100 mA
Power
Power consumption, typ.	max. 2.5 W
EMC
Interference immunity against discharge of static electricity
Interference immunity against discharge of static electricity acc. to IEC 61000-4-2	Yes; 6 kV, contact discharge (to IEC 61000-4-2); 8 kV, air discharge (to IEC 61000-4-2)
Interference immunity to cable-borne interference
on the supply lines acc. to IEC 61000-4-4	Yes; 2 kV (to IEC 61000-4-4, burst)
Interference immunity on signal lines acc. to IEC 61000-4-4	Yes; 1 kV (to IEC 61000-4-4; burst; length < 3 m); 2 kV (to IEC 61000-4-4; burst; length > 3 m)
Surge immunity
on the supply lines acc. to IEC 61000-4-5	Yes; 1 kV (to IEC 61000-4-5; surge symm.); 2 kV (to IEC 61000-4-5; surge asymm.)
Immunity against high-frequency electromagnetic fields
Interference immunity against high-frequency radiation acc. to IEC 61000-4-3	Yes; 10 V/m, 80 to 1000 MHz (to IEC 61000-4-3); 10 V/m, 900 MHz, 1.89 GHz, 50% ED (to IEC 61000-4-3)
Immunity against conducted interference induced by high-frequency fields
Interference immunity against high frequency current feed acc. to IEC 61000-4-6	Yes; 10 V, 9 kHz to 80 MHz (to IEC 61000-4-6)
Immunity to magnetic field interference
Interference immunity to magnetic fields at 50 Hz	30 A/m; to IEC 61000-4-8
Emission of radio interference acc. to EN 55 022
Interference emission acc. to EN 55022, class B	Yes
Ambient conditions
Operating temperature
Min.	5 °C
max.	40 °C
Permissible temperature change	10 °C/h; Operation: 10 K/h; storage/transport: 20 K/h
Storage/transport temperature
Min.	-20 °C
max.	60 °C
Relative humidity
Operation, min.	5 %
Operation, max.	80 %; At 25 °C (no condensation)
Storage/transport, min.	5 %
Storage/transport, max.	95 %; At 25 °C (no condensation)
Vibrations
Operation, checked according to IEC 60068-2-6	Yes; 10 to 58 Hz: Amplitude 0.075 mm; 58 to 500 Hz: Acceleration 9.8 m/s2
Transport tested checked to IEC 60068-2-6	Yes; (packed) 5 to 9 Hz, amplitude 3.5 mm; 9 to 500 Hz, acceleration 9.8 m/s2
Shock test
Shock test	Tested to DIN IEC 60068-2-2; Operation: 950 m/s2 (10 g), 30 ms, 100 Shocks; Transport (packaged): 250 m/s2 (25 g), 6 ms, 1000 shocks
Dimensions
Width	105 mm
Height	58 mm
Depth	26 mm
Weight
Weight, approx.	100 g

Our company have the compatible cable, named USB/MPI+ V2.0,  can replace Siemens 6ES7 972-0CB20-0XA0.

Below is the picture of our compatible OEM product USB/MPI+ V2.0:

You can get it only need USD90.00/pc.    Buy now ====>

It’s tested before shippment.Not made by Siemens,OEM product as the replacement.

The quality is guaranteed, we have 1 year warranty for our compatible products.

This is USB/MPI+ V2.0 only for Siemens S7-300/400 PLC.

Optoelectronic isolated USB/MPI V2.0,Siemens S7-300/400 PLC Programming adapter cable,3 meters,with communication indicator,can replace Siemens 6ES7 972-0CB20-0XA0,automatically adjust the communication speed from 19.2Kbps to 115.2Kbps for the PC port,automatically adjust the communication speed from 19.2Kbps to 187.5Kbps for the MPI interface.It doesn’t support profibus function.

USB/MPI+ is the optoelectronic isolated adapter for industrial design. There is anti-surging& anti-lightning protection circuit for the USB and RS485 interface. It support hot plug. It‘s suitable for the communication between Siemens S7-300/400 series PLC or other equipments with MPI interface and computer. In particular, it applies to the strong interfere industrial scene and the safeguard in the circuit guarantees the safely running of the system.

USB/MPI+ programming cable simulate USB port as traditional serial port (usually COM3), which enables existing programming software(STEP 7) to communicate through simulated traditional port and PLC devices.

Usage:
USB device drivers should be installed before using USB/MPI+ programming cable. After completing Driver installation, the corresponding COM port for the USB/MPI+ programming cable will be displayed in the  Device Manager of Window. The step next is just to choose this COM port in the programming software and other application software and keep other communication parameters as in the Default settings. And the following steps are exactly the same as in the traditional programming cables with RS232 interfaces. Here are requested to indicate that “USB” option in the local communications interface setting which the software is not support to the programming cable.

If the COM port in the programming software with “*” symbols, such as “* COM3″, it’s shown that the COM port have faults. Quit the software and plug a USB plug or re-install the USB driver.

Please note that Siemens COM port in programming software is up to support the option to COM8.But the ports more than COM8 are able to choose but in fact can not be used!

STEP7 software settings:
Enter the main interface of STEP7 programming software (SIMATIC Manager), click on the “Set PG / PC Interface ” option under “Options” menu into the PG / PC interface settings.

1, Double-click on “PC Adapter (MPI)” to set the parameters of COM port and MPI port. The adapter does not support “PC Adapter (PROFIBUS)” option.

2, Click on “Local Connection” option to set the parameters of COM port, correct choose the COM port in the equipment manager after the driver of USB / MPI + USB has been installed, select the 19200 bps or 38400 bps as the baud rate of COM Communication. USB / MPI + will automatically adapt to the choice of baud rate.

3, Click “MPI” to set the parameters of MPI interface adapter options, baud rate can be set to 187.5 Kbps, or 19.2 Kbps, USB / MPI + adapter will automatically adapt to the MPI port of the PLC baud rate. Other parameters set as default.

4, On-line test can access the points: USB / MPI + connect the MPI port of the S7-300/400PLC with the computer’s USB port. Click on the main menu interface, as shown in a red circle button. If the data in red box is shown as the picture, the on-line test has pasted. As so far, the setting has completely finished. It can do all Operation such as upload, download ,monitoring of the procedures and other operations.

Long-distance communications:

For USB/MPI+, the largest communication distance is up to 1000m at the communication speed of 187.5Kbps. It needs to splice 120ohm terminal resistance between 3 and 8 pin on the RS485 port(DB9 Male) to eliminate signal reflection, and connect 24VDC power between 7 and 2 pin. But requires one PFB-G for each PLC.

Please Note: USB interface cable cannot be extended.

The quality is guaranteed.It’s tested before shippment.Not made by Siemens,OEM product as the replacement.

Any question, please feel free to contact me.

USB/MPI+ V4.0:USB to RS485 isolated adapter for SIEMENS S7-200/300/400 PLC,replace 6ES7 972-0CB20-0XA0

USB/MPI+ V4.0:USB to RS485 isolated adapter for SIEMENS S7-200/300/400 PLC,replace 6ES7 972-0CB20-0XA0

6ES7 972-0CB20-0XA0          SIMATIC S7, PC ADAPTER USB

SIMATIC S7, PC ADAPTER USB F. CONNECTION OF S7-200/300/ 400, C7; WITH USB-CABLE (5M) CAN BE USED UNDER WINXP/VISTA/ WINDOWS 7 32/64BIT

Please read below data sheet of Siemens original 6ES7972-0CB20-0XA0:

-	SIMATIC S7, PC ADAPTER USB F. CONNECTION OF S7-200/300/ 400, C7; WITH USB-CABLE (5M) CAN BE USED UNDER WINXP/VISTA/ WINDOWS 7 32/64BIT
Supply voltage
24 V DC	Yes
Input current
Current consumption, typ.	100 mA
Power
Power consumption, typ.	max. 2.5 W
EMC
Interference immunity against discharge of static electricity
Interference immunity against discharge of static electricity acc. to IEC 61000-4-2	Yes; 6 kV, contact discharge (to IEC 61000-4-2); 8 kV, air discharge (to IEC 61000-4-2)
Interference immunity to cable-borne interference
on the supply lines acc. to IEC 61000-4-4	Yes; 2 kV (to IEC 61000-4-4, burst)
Interference immunity on signal lines acc. to IEC 61000-4-4	Yes; 1 kV (to IEC 61000-4-4; burst; length < 3 m); 2 kV (to IEC 61000-4-4; burst; length > 3 m)
Surge immunity
on the supply lines acc. to IEC 61000-4-5	Yes; 1 kV (to IEC 61000-4-5; surge symm.); 2 kV (to IEC 61000-4-5; surge asymm.)
Immunity against high-frequency electromagnetic fields
Interference immunity against high-frequency radiation acc. to IEC 61000-4-3	Yes; 10 V/m, 80 to 1000 MHz (to IEC 61000-4-3); 10 V/m, 900 MHz, 1.89 GHz, 50% ED (to IEC 61000-4-3)
Immunity against conducted interference induced by high-frequency fields
Interference immunity against high frequency current feed acc. to IEC 61000-4-6	Yes; 10 V, 9 kHz to 80 MHz (to IEC 61000-4-6)
Immunity to magnetic field interference
Interference immunity to magnetic fields at 50 Hz	30 A/m; to IEC 61000-4-8
Emission of radio interference acc. to EN 55 022
Interference emission acc. to EN 55022, class B	Yes
Ambient conditions
Operating temperature
Min.	5 °C
max.	40 °C
Permissible temperature change	10 °C/h; Operation: 10 K/h; storage/transport: 20 K/h
Storage/transport temperature
Min.	-20 °C
max.	60 °C
Relative humidity
Operation, min.	5 %
Operation, max.	80 %; At 25 °C (no condensation)
Storage/transport, min.	5 %
Storage/transport, max.	95 %; At 25 °C (no condensation)
Vibrations
Operation, checked according to IEC 60068-2-6	Yes; 10 to 58 Hz: Amplitude 0.075 mm; 58 to 500 Hz: Acceleration 9.8 m/s2
Transport tested checked to IEC 60068-2-6	Yes; (packed) 5 to 9 Hz, amplitude 3.5 mm; 9 to 500 Hz, acceleration 9.8 m/s2
Shock test
Shock test	Tested to DIN IEC 60068-2-2; Operation: 950 m/s2 (10 g), 30 ms, 100 Shocks; Transport (packaged): 250 m/s2 (25 g), 6 ms, 1000 shocks
Dimensions
Width	105 mm
Height	58 mm
Depth	26 mm
Weight
Weight, approx.	100 g

Our company have the compatible cable, named USB/MPI+ V4.0,  can replace Siemens 6ES7 972-0CB20-0XA0.

Below is the picture of our compatible OEM product USB/MPI+V4.0:

You can get it only need USD99.99/pc.    Buy now ====>

It’s tested before shippment.Not made by Siemens,OEM product as the replacement.

The quality is guaranteed, we have 1 year warranty for our compatible products.

Introduction

USB/MPI+ V4.0 is the USB to MPI and PPI protocol adapter, support S7-300/400 PLC MPI or S7-200 PLC PPI communication. It’s the same as Siemens PC Adapter USB except that this USB/MPI+ V4.0 doesn’t support profibus communication. Its driver is the Siemens PC_Adapter_USB driver, and choose the USB port, not the COM port.

The working power supply of this cable USB/MPI+ V 4.0 is directly from the USB port, but not the PLC programming interface.

USB/MPI+ V 4.0 is the optoelectronic isolated adapter for industrial design. There is anti-surging& anti-lightning protection circuit for the USB and RS485 interface. It support hot plug. It’s suitable for S7-300/400/200 series PLC. In particular, it applies to the strong interfere industrial scene and the safeguard in the circuit guarantees the safely running of the system.

USB/MPI+ principle and figure structure:

Indicator State

Functions
●    Support STEP7 V5.2 and higher,STEP7 Micro/Win 4.0 and higher
●    Fully compatible with USB V2.0
●    Power supply by USB port(100mA). with overcurrent Protection and Surge Protection
●    High optoelectronic isolation voltage up to 1000VDC
●    The USB port design with surge protection.
●    The RS485 port design with overcurrent protection and lightning
protection:Ipp=100A(10/700us,4KV) .Accord to the standard:ITU-TK20/21,VDE0433. ±15KV ESD Protection.
●    Baud rate of MPI port on PLC: 19.2Kbps,187.5Kbps,1.5Mbps. automatically adjust.
●    Baud rate of PPI port on PLC: 9.6Kbps,19.2Kbps,187.5Kbps.
automatically adjust.
●    Support long distance communication up to 1000m
●    Working temperature -20~+75′C
●    Length 3 meters.Color:black
●    One pc supports one USB programming cable only

About Long Distance Communication
For USB/MPI+ V4.0, the largest communication distance is up to 1000m at the communication speed of 187.5Kbps. It needs to splice 120ohm terminal resistance between 3 and 8 pin on the RS485 port(DB9 Male) to eliminate signal reflection. But requires one PFB-G for each PLC.

Please contact me if you have any question.

OP programming cable: replace 6XV1 440-2KH32

OP programming cable: replace 6XV1 440-2KH32

 

You can get it only need USD18.00/pc.    Buy now ====> 

It’s tested before shippment.Not made by Siemens,OEM product as the replacement.

The quality is guaranteed, we have 1 year warranty for our compatible products.

 

Please feel free to contact me if you have any question.

 

MPI cable:Cable between S7-200/300 PLC and Siemens touch panel, 6ES7901-0BF00-0AA0.

MPI cable:Cable between S7-200/300 PLC and Siemens touch panel, 6ES7901-0BF00-0AA0.

-	SIMATIC S7, MPI CABLE FOR CONNECTING SIMATIC S7 AND PG VIA MPI 5M
Cables
belongs to product	MPI
Cable length	5 m
Weight
Weight, approx.	293 g

LOGO!USB-CABLE:USB isolated adapter for Siemens LOGO! Replace Siemens 6ED1057-1AA01-0BA0.

LOGO!USB-CABLE:USB isolated adapter for Siemens LOGO!
Can replace Siemens original 6ED1057-1AA01-0BA0.

USB optoelectronic isolated cable for Siemens LOGO!,2.5 meters,with communication indicator.

LOGO! USB-CABLE is a programming cable which use the USB interface to achieve the serial connection and the conversion of peripheral port signal. Under the control of computer operation,simulating the computer’s USB interface to traditional serial(commonly known as COM port),thus using the current programming software,communicating software and monitoring software.The work power of the cable comes from USB port and programming port of LOGO! controller.

USB-CABLE is photoelectric isolated,can be applied to LOGO! Controller，especially the industrial fields with greater interference and easily damaged communication port. All kinds of protection measures in the circuit give permission to the safe operation of the system.

LOGO!USB-CABLE’ s chart appearance：

Characteristics and specifications：

● Support USB-CABLE programming software version：LOGO! Soft V4.0 and above
● Fully compatible with standard USB V2.0
● Power supplied by USB bus and the programming port of LOGO! Controller.
● Optical isolation voltage：1000VDC
● Support UART data format：Data：7、8，stop bit：1、2，check：odd/even/no parity
● Each PC only supports one USB cable
● Working temperature：-20～+75℃
● Cable length：2.5m，color：black

System requirement

Please make sure your PC is IBM PC compatible and has the following system requirements before using the USB programming cable.

● Intel is compatible with 586DX4-100MHz CPU or higher

● A standard USB port (4-pin A plug)

● Operating system is Windows2000 or Windows XP

Setting of LOGO!Soft-Comfort

After completing the driver installation,In the Windows Device Manager will come up the COM port of USB-CABLE programming cable,just in the programming of software or other software applications,selecting the COM port.And the follow applyment is exactly the same as the traditional RS232 programmng cable.

Open the main windows form(LOGO!Soft-Comfort),choose “Tools” menu then click “Options…” sub menu and will appear Options setting window.

Select “Interface” Item in the left list,and Choose the COMX interface as it in the Device Manager.

Applications：
USB-CABLE programming cable can only be used under the device of USB. After completing the driver installation，In the Windows Device Manager will come up the COM port of USB-CABLE programming cable，just in the programming of software or other software applications，selecting the COM port.And the follow applyment is exactly the same as the traditional programming cable.

Note: The maximum extension of the USB cable could reach 5 meters.

The quality is guaranteed.It’s tested before shippment.Not made by Siemens,OEM product as the replacement.

 

For any question, please feel free to contact me.

 

LOGO!PC-CABLE:RS232 isolated cable for Siemens LOGO! 6ED1 057-1AA00-0BA0

LOGO!PC-CABLE:RS232 isolated cable for Siemens LOGO! 6ED1 057-1AA00-0BA0

-	LOGO! PC CABLE, F. THE TRANSMISSION OF PROGRAMS FROM PC TO LOGO! AND VICE VERSA
Cables
belongs to product	LOGO!
Cable length	3 m
Weight
Weight, approx.	168 g

Now, only need USD43.00, you can get it.  Buy now  =======>

PC/MPI: RS232 Programming adapter for Siemens S7-300 PLC can replace Siemens 6ES7972-0CA23-0XA0

PC/MPI: RS232 Programming adapter for Siemens S7-300 PLC  can replace Siemens 6ES7972-0CA23-0XA0

Now, only need USD71.00, you can get it.     Buy now ====>

PC/MPI+: RS232 isolated Programming adapte for Siemens S7-300/400 PLC,6ES7972-0CA23-0XA0

PC/MPI+:  RS232 isolated Programming adapte for Siemens S7-300/400 PLC,6ES7972-0CA23-0XA0

SIMATIC S7, PC ADAPTER V5.1 FOR CONNECTION OF S7-300/400, C7, M7; FOR CONVERSION OF RS232 TO RS485; W/O RS232 CABLE

Our company have the compatible cable, named PC/MPI+,including RS232 cable,  can replace Siemens original 6ES7972-0CA23-0XA0.

Please look at below picture of our compatible PC/MPI+ including RS232 cable :

You can get it only need USD90.00/pc.    Buy now ====> 

When you buy PC/MPI+,we will give you the free RS232 Cable.

It’s tested before shippment.Not made by Siemens,OEM product as the replacement.

The quality is guaranteed, we have 1 year warranty for our compatible products.

Description of our compatible PC/MP+  :

Optoelectronic isolated RS232/MPI,Siemens S7-300/400 PLC Programming adapter cable,with communication indicator,can replace Siemens 6ES7 972-0CA23-0XA0,automatically adjust the communication speed from 19.2Kbps to 115.2Kbps for the PC port,automatically adjust the communication speed from 19.2Kbps to 187.5Kbps for the MPI interface.Can connect PLC and the touch panel of third party factory to communicate.It doesn’t support profibus function.

PC/MPI+ adapter, or named PC adapter, could achieve the level conversion of RS232 to RS485 and the protocal conversion of RS232 to MPI(MultiPoint Interface).PC/MPI+ is the adapter of photoelectric isolation type towards industrial design. Between RS232 port and RS485 port exist the surge protection and anti-lightning protection circuit, adaptable to the full PLC series of Siemens S7-300/400 and those devices with MPI port, especially the industrial fields with greater interference and easily damaged communication port. All kinds of protection measures in the circuit give promission to the safe operation of the system.

PC/MPI+ can make touch-screen communications with the third party under the link of S7-300/400PLC, such as eView, Wei-lun and kun-lun state.

Characteristics and main technical parametres:

★ Power: It is supplied by the 24VDC MPI port of PLC, power consumption of about 1w, with overcurrent protection and surge protection.
★ Isolation Voltage: 1000VDC(Maximun to 3000 VDC, orders require statement.)
★ RS232 port has anti-surge protection, RS485 port has anti-lightning protection and overcurrent protection with the consumption of 500w.
★ RS232 port baud rate: 19.2Kbps—115.2Kbps, automatically adaptable to the standard baud rate.
★ MPI port baud rate: 187.5Kbps—19.2Kbps, automatically adaptable.
★ Supporting the connection of PLC to touch-screen communication with the third party.
★ With a power indicater light, on-line and data transmission indicater light.
★ Working temperature: -20～75′C
★ Dimension: 103×50×26; After connecting the RS232 cables: 5.5m.

RS232 adapter port and port-pin RS485 signal definations:

 RS232-Block(DB9M) defination signals RS485-Block(DB9M) defination signals

 Instructions of the indicater light

Software settings of STEP7:
Entering the main interface of STEP7 programming software(SIMATIC Manager), clicking on “Options” menu under the “Set PG/PC Interface…” option into the PG/PC interface settings.
1. Double clicking on “PC Adapter(MPI)” into the RS232 interfaces and MPI set of parameters. The adapter does not support “PC Adapter(PROFIBUS)” option.
2. Clicking on “Local Connection” option set RS232 interface parameters, choosing PC/MPI to connect on the port of COM correctly, and it will adapt to the chosen baud rate automatically, both 19200bps and 38400bps of RS232 communication.
3. Clicking “MPI” to set port parameters of adapter MPI, acceptable at both 187.5Kbps and 19.2Kbps, and the adapter will adapt to its baud rate automatically. Others have already been set.
4. On-line test accessing point: Using PC/MPI to connect to MPI port and RS232 port of the computer. And then click on the button in the red circle as follow, if appearing the data inside the red line, the test has passed. Then one could operate on it.

The long-distance communication of PC/MPI+ adapter:

1. To extend the distance of RS485 port:

2. To extend the distance of RS232 port:

RS232 Cable:

When you buy PC/MPI+,we will give you the free RS232 Cable.

The quality is guaranteed.It’s tested before shippment.Not made by Siemens,OEM product as the replacement.

PC/PPI+:RS232 to PPI optoelectronic isolated adapter for Siemens S7-200 PLC,replace 6ES7 901-3CB30-0XA0