Profibus Connector

6ES7332-5HD01-0AB0 Siemens Analog output module

Introduction to Siemens 6ES7332-5HD01-0AB0

 

Properties of Siemens 6ES7332-5HD01-0AB0
● 4 outputs in one group
● The output can be selected by individual channel
– Voltage output
– Current output
● Resolution 12 bits
● Programmable diagnostics and diagnostic interrupt
● Electrically isolated to backplane bus interface and load voltage
● Supports parameter reassignment in RUN
Diagnostics
For information on diagnostic messages at the "group diagnostics" parameter, refer to
chapter Diagnostic messages of analog output modules (Page 310).
Terminal assignment
The diagrams below show various wiring options.
Note
When you switch the rated load voltage (L+) off and on, the outputs can return incorrect
voltage/current values for the duration of about 500 ms.

 

Wiring: 2 and 4-wire connection for voltage output
The following Fig. represents the 2-wire connection with no compensation for line resistors
and the 4-wire connection with compensation for line resistors.

Wiring: Current output

 

Technical specifications of 6ES7332-5HD01-0AB0

	SIMATIC S7-300, ANALOG OUTPUT SM 332, OPTICALLY ISOLATED, 4 AO, U/I; DIAGNOSTICS; RESOLUTION 11/12 BITS, 20 PIN, REMOVE/INSERT W. ACTIVE, BACKPLANE BUS
Supply voltage
Load voltage L+
Rated value (DC)	24 V
Input current
from load voltage L+ (without load), max.	240 mA
from backplane bus 5 V DC, max.	60 mA
Power losses
Power loss, typ.	3 W
Analog outputs
Number of analog outputs	4
Voltage output, short-circuit protection	Yes
Voltage output, short-circuit current, max.	25 mA
Current output, no-load voltage, max.	18 V
Output ranges, voltage
0 to 10 V	Yes
1 to 5 V	Yes
-10 to +10 V	Yes
Output ranges, current
0 to 20 mA	Yes
-20 to +20 mA	Yes
4 to 20 mA	Yes
Load impedance (in rated range of output)
with voltage outputs, min.	1 kΩ
with voltage outputs, capacitive load, max.	1 µF
with current outputs, max.	500 Ω
with current outputs, inductive load, max.	10 mH
Cable length
Cable length, shielded, max.	200 m
Analog value creation
Integrations and conversion time/ resolution per channel
Resolution with overrange (bit including sign), max.	12 bit; +/-10 V, +/-20 mA, 4 to 20 mA, 1 to 5 V: 11 bits + sign; 0 to 10 V, 0 to 20 mA: 12 bits
Conversion time (per channel)	0.8 ms
Settling time
for resistive load	0.2 ms
for capacitive load	3.3 ms
for inductive load	0.5 ms; 0.5 ms (1 mH); 3.3 ms (10 mH)
Errors/accuracies
Operational limit in overall temperature range
Voltage, relative to output area	+/- 0,5 %
Current, relative to output area	+/- 0,6 %
Basic error limit (operational limit at 25 °C)
Voltage, relative to output area	+/- 0,4 %
Current, relative to output area	+/- 0,5 %
Interrupts/diagnostics/status information
Substitute values connectable	Yes; Parameterizable
Alarms
Diagnostic alarm	Yes; Parameterizable
Diagnostic messages
Diagnostic information readable	Yes
Diagnostics	Yes
Diagnostics indication LED
Group error SF (red)	Yes
Galvanic isolation
Galvanic isolation analog outputs
between the channels and the backplane bus	Yes
Isolation
Isolation checked with	500 V DC
Connection method
required front connector	20-pin
Dimensions
Width	40 mm
Height	125 mm
Depth	120 mm
Weight
Weight, approx.	220 g

 

Parameter reassignment in RUN
If you reassign parameters in RUN, the following special characteristic applies.
SF LED is lit:
If a diagnostics was pending prior to reconfiguration, the SF LEDs (on CPU, IM or module)
may be lit even though diagnostics is no longer pending and the module is operating correctly.
Solution:
● Only assign new parameters if no diagnostics is pending, or
● unplug module and plug it in again.

 

Output ranges of SM 332; AO 4 x 12 Bit
Introduction
You can configure the outputs for operation as voltage or current outputs, or disable them.
You program the outputs at the "output type" parameter in STEP 7.
The output type "Voltage" and output range "± 10 V" are set by default at the module. You
can always use this combination of output type and range without having to program the
SM 332; AO 4 x 12 Bit in STEP 7.
Output ranges
Program the voltage and current output ranges in STEP 7.
Output ranges of SM 332; AO 4 x 12 Bit

Selected type of output	Output range
Voltage	1 V to 5 V 0 V to 10 V
	± 10 V
Current	0 mA to 20 mA
	4 mA to 20 mA
	± 20 mA

 

Overview of the parameters of SM 332; AO 4 x 12 Bit

 

Assigning parameters to channels
The parameters can be set separately at each output channel of SM 332; AO 4 x 12 Bit. You can assign separate parameters to each output channel.
Assign the parameters you set at the SFCs in the user program to the channel groups. Each output channel of SM 332; AO 4 x 12 Bit is thus assigned to a channel group, i.e. output channel 0 > channel group 0, for example.

Note
The output may carry incorrect interim values if you modify output ranges while SM 332;AO 4 x 12 Bit is in RUN.

Additional information on SM 332; AO 4 x 12 Bit

Unused channels
To take unused output channels of SM 332; AO 4 x 12 Bit off power, set the "disabled" argument at the "output type" parameter. Disabled channels do not have to be wired.
Line continuity check
SM 332; AO 4 x 12 Bit only performs a line continuity check at the current outputs.In output ranges 0 mA to 20mA and ±20 mA, a "reliable" wire-break check is not possible for output values of-20s to ±200 μA.
Short-circuit test
SM 332; AO 4 x 12 Bit only performs a short-circuit test at the voltage outputs.
Substitute values
You can configure the SM 332; AO 4 x 12 Bit for CPU STOP mode as follows: Outputs off power, hold last value or set substitute values. The set substitute values must lie within the output range.

 

 

USER'S manual PDF of 332-5HD01, please refer from Page 481- Page 489:

 

S7-300 Modules data & USER'S MANUAL

 

Our company (Kollewin Technology CO., Limited) have a new product,

named 6ES7332-5HD01-0AB0,

it is 100% compatible with Siemens original part.

Part#: 6ES7332-5HD01-0AB0

Unit price:USD310.00/pc    

Description: S7-300 Analog onput module
Manufacturer: Kollewin
Approx. Weight: 0.3 Kg
Warranty: 1 year
Origin: China

Here, you also need 1 piece of 20pin front connector to connect with it.

Our compatible 6ES7 392-1AJ00-0AA0 can meet your requirements.

 

6ES7 392-1AJ00-0AA0  @USD10.50/pc  

 

Technical data sheet of our SM 332  6ES7332-5HD01-0AB0

Model	SM332 4AO
Product  Description	4AO;  Resolution:12bits; High-accuracy
Power consumption
·From bus current consumption	40mA
·From L+	40mA
·Power loss	3W
Number of analog outputs	4
Load voltage+rated value	24V
Shielded cable length,Max	200m
Voltage output, Max,short circuit Current	Yes
Voltage output, Short circuit current(Max)	25mA
Voltage output, Open-circuit current,Max	18V
Load impedance
·Voltage outputs,Min	1KΩ
·current outputs,Max	500Ω
Output ranges
·voltage	±10V,0~10V,1~5V
·current	±20mA,0~20mA,4~20mA
D/A resolution	12bit
conversion time(per channel)	Max:0.8ms
Setting time
·Resistive loads	0.1ms
·Capacitive loads	3.3ms
·Inductive loads	0.5ms
Output cross talk	>40dB
Tolerance(Over entire temperature range)
·Voltage output	±0.5%
·Current output	±0.6%
Diagnostic interrupt	None
Group fault error	Red LED
Isolution tested for contact
·Between channels and backplane bus	Yes
·Between channels and load voltage L+	Yes
Front connector	20-pin
Dimensions(W x H x D)(mm)	40×125×120
Order Number	332-5HD01-0AB0

 

Picture of 6ES7332-5HD01-0AB0

 

More compatible Siemens S7-200/300 modules we can offer：

 

More pictures for your reference:

 

Please feel free to contact me for any question!

Contact person: Miss Nancy